KAOS: Installation Instructions - Inside Mount

---

Step 1: END CAP INSTALLATION

• Verify your order to confirm the correct side for the motor before installing the corresponding end cap.
• Refer to the illustrated instructions for proper mounting, whether for a ceiling or wall installation.

---

---

---

Step 2: END CAP INSTALLATION

• Attach an end cap to each end of the housing using the three provided self-tapping screws.

---

Step 3: HOUSING INSTALLATION

• Use a drill with the appropriate bit size to pre-drill holes, considering the type of surface where the unit will be installed.
• Drill holes through the cassette to accommodate the power cord, and use the grommet to protect the cable from damage.

---

Step 4: HOUSING INSTALLATION

• Position the back part of the housing at the desired location.

• Secure the housing in place with the appropriate screws, based on mounting surface material.

---

Step 5: HOUSING INSTALLATION

• Secure the housing in place with the appropriate screws, based on mounting surface material.

---

Step 6: U-CHANNEL INSTALLATION

• Measuring and Cutting U-Channels and Tracks:
  • Measure the distance from the ground surface to the bottom of the cassette.
  • Based on that measurement, cut the U-channels and tracks to be 1/4” shorter.
  • Important: Only cut from the bottom section of the track.

---

Step 7: U-CHANNEL INSTALLATION

• Pre-drill the U-channel:
  • 2 holes for TOP, MIDDLE and BOTTOM.
  • 1 hole every 12 inches in spacing Attach the U-Channel beneath the housing, ensuring it is aligned with the back of the housing.

---

Step 8: U-CHANNEL INSTALLATION

• Secure the U-channels on both sides using the appropriate screws.

---

Step 9: MATERIAL ROLL INSTALLATION

• To make this step easier, support the weight bar as shown below while you proceed with the installation.

---

Step 10: MATERIAL ROLL INSTALLATION

• With the weight bar resting on the support, begin unwinding the shade material.
• Manage the cable through the rubber grommet.
• Attach the motor head to the motor bracket and secure it using the provided clip.

---

Step 11: MATERIAL ROLL INSTALLATION

• Insert the Idler into its bracket and secure it with the provided pin.

---

Step 12: MATERIAL ROLL INSTALLATION

• Align the shade material so the Keder hangs over the edge of the outer tube.
• Confirm that the shade is centered, and secure it using the provided screws.

---

Step 13: MATERIAL ROLL INSTALLATION

• Once the tube is secured in place, use the remote control to roll up the shade material.
• KAOS: Alpha Motor Programming Guide
• KAOS: Somfy Motor Programming Guide

---

Step 14: TRACK INSTALLATION

• Tuck each end of the weight bar into the U-channel

---

Step 15: TRACK INSTALLATION

• With the weight bar inside the U-channel, roll the material up until it’s about 12” from the top of the U-channel.

---

Step 16: TRACK INSTALLATION

• Slide the V-tracks at an angle into the U-channels. While doing this, manually lift the weight bar to insert the keder into the V-track, ensuring the wheels are aligned within the V-track.

---

Step 17: TRACK INSTALLATION

• Ensure the wheels are correctly positioned and properly aligned with the track for smooth operation.

---

Step 18: TRACK INSTALLATION

• Install the wheel stopper as shown in the illustration to prevent the wheel system from coming off the tracks.

---

Step 19: TRACK INSTALLATION

• To adjust un-level material:
  • Unroll the shade material until the leveling tube screws are visible.
  • Loosen the screws and adjust the slider as needed.

---

Step 20: SECURING TRACK

• Place the track jig on the back of the U-channel, align it with the edge of the track, mark the position, and drill a hole 1.5” deep.

---

Step 21: SECURING TRACK

• Secure the track to the U-channel using 1 1/2” flanged screws. (not included)

---

Step 22: COVER INSTALLATION

• Install the cover and secure it using two of the provided end cap screws.
• One screw for each end.
• Note: Do not over tighten the screws

---

• NOTE: If the external cover screw holes are inaccessible, use the cover jig to assist in locating the internal cover screw holes.

NOTE: If the cover jig tabs do not fit between the end of the cassette and the wall, break them off. Gently work the plastic tabs back and forth until they detach completely.

---

Depending on the motor you ordered with your shade, refer to the guides below:

KAOS: Alpha Motor Programming Guide

KAOS: Somfy Motor Programming Guide

---

---

For issues, contact Screen Innovations:
Phone: [phone] Option 3
Website: www.screeninnovations.com