Solo 3: Indoor 575/675 External Mount - Mounting the Cassette - METHOD 2

---

OPERATING AND CARE OF YOUR SCREEN

• Operation of the screen systems should only be performed by responsible parties.
• Always check the path of the Solo 3 Screen before operating to ensure that the path is clear of furniture or obstacles that could prevent full operation.
• Monitor the Solo 3 Screen for smooth operation through its entire range.
• Operating a Solo 3 Screen unattended may lead to damage from obstructions or other causes.
• Fabric maintenance and cleaning– Solo 3 Screen fabric is subject to debris under normal use or in storage, requiring occasional maintenance and cleaning.
• While fading and wear over time are normal, debris could accelerate this wear.
• Screen fabrics can be cleaned with gentle soap and water. 

---

BEFORE PROCEEDING

Read the instructions in their entirety before proceeding. Actions contrary to the instructions invalidate the warranty and may result in serious damage and/or injury.

Preparing for installation: It is crucial that all installations are planned out carefully before specifying a screen order.

• If drilling through the cassette is required, the cassette must be square or the door will not line up, causing poor operation.
• Electrical work should be performed following appropriate electrical codes and regulations by a licensed electrical professional.
• Use fasteners appropriate for the structure the Solo 3 Screen will be mounted to.
• Do not use any sharp blades when opening the packaging.

---

INSTALLATION METHODS

Before installation, determine your installation method according to your product order and installation preferences. The indoor Solo 3 675 External may be installed preassembled or separately (fabric tube and material installed after the cassette).

• METHOD 1 – Assembled
  • Solo 3: Indoor 675 External Mount - Mounting the Cassette - METHOD 1
• METHOD 2 – Disassembled (Cassette only)

---

• To ensure best results, read all instructions before assembly.
• Unpacking the box– lay cassette, fabric tube, and material roll on a soft, clean surface during the installation process.
• When removing from the box, ensure the assembly is kept horizontal to prevent damage. • The following section, Mounting, of the indoor Solo 3 675 External instructions applies to ALL installations, regardless of method, determined above.
• When utilizing either method, especially METHOD 1, make certain there are enough installers/ hoisting equipment to safely lift the cassette (and/or material) onto the brackets.
• Brackets must be level and in-line with one another before attempting to lift cassette onto brackets.
• Use safe lifting and rigging techniques.

---

Method 2

Step 1: INSTALLATION – UNPACKING

• The following section of the Solo 3 Indoor 675 External instructions applies to separately assembled projects where the cassette is installed prior to the fabric tube and material. 
• Starting with the cassette on a soft, clean surface, remove the screws from the fascia door and open to reveal the inside. 

---

Step 2: INSTALLATION – UNPACKING

• Remove both of the exposed red weight bar clips (2) by removing the attached screws from the 2 brackets.

---

Step 3: INSTALLATION – MATERIAL ROLL REMOVAL

• Undo the silver safety screws, then press the latch as shown.

---

Step 4: INSTALLATION – MATERIAL ROLL REMOVAL

• Using the red straps, loop the straps under the material roll, being careful to avoid contact with the material or any obstructions.
• With the help of the straps on both the ends, slowly pull out material roll and set it aside.

Step 5: INSTALLATION – MATERIAL ROLL REMOVAL

• Remove the clips from the end of the weight bar, and attach the magnetic end caps

---

Step 6: INSTALLATION – INSTALLING THE CASSETTE

• Installation requires two or more people and/or hoisting equipment.
• Please use safe lifting and rigging techniques.

Wall Mount

---

Ceiling Mount

• Lift and secure the cassette onto the brackets.
• Once the bracket engages, the cassette will “click” into place.

---

Step 7: INSTALLATION – MATERIAL ROLL REINSERTION

• With the cassette mounted, open the door and slide the material roll with mounting plates on each end into the cassette.
• Each end will “click” into place as the brackets engage. 
• The roll must remain level while installing into the cassette.

---

Step 8: INSTALLATION – MATERIAL ROLL REINSERTION

• Fasten the silver safety screws on the mounting plates to secure the material roll.
• Plug motor power cable into the barrel connector located in the cassette.
• This step is required for safety. Back safety screws out before installation. Must be re-engaged after installing material roll.

---

Step 9: INSTALLATION – FASCIA DOOR

• To close the fascia door, set the door into the cassette; the door will hook in by gravity.
• Secure with screws. 

---

For issues, contact Screen Innovations:
Phone: [phone] Option 3
Website: www.screeninnovations.com